1 x R-W50 Electric Lock
1 x RFID Password Keypad
1 x Exit Button
2/4/6 x Remote Control
1 x Screw Kit
Wireless contecting,no wired.Easy Installtion 9 Seconds Auto Locked
The lock design is suit for most of the door. Please note this lock must installing in door. You can see more installing case in the following pictures.
① Lock pin
Using 45# steel very sturdy and durable.
② Emergency unlock button
To quickly unlock and escape in emergency situation.
1）It is forbidden to use non-emergency situation.
2）Once use the emergency unlock button, the automatic locking function will be closed. Only receives the decoding command on the remote control, automatic locking function can open again.
③ Unlock button indoor
When use is indoor, can use it open the lock.
④ Indicator light
In the following operation or it alarm, the indicator light will lit up
1）When the lock is open or closed
2）When start the match code button to match the code；
3）When the battery voltage is lower than 2.5 V, the lock alarm
⑤The match code button
Add or delete the remote control.
⑥ Open button
┻ ON Open position function.
┻ OFF Press the button to close the lock function
If it don\'t automatically locked ,the remote control will lose efficacy.
⑦ Adjust the lock hasp install plate
After finish install the main lock and vice lock, if the main lockpin can’t be insert into the hole of the pin plate because of the height of the lock is different, user can adjust the height of the pin plate which was located by 2 M5 screws .
⑧Automatically closed magnet switch
1）Automatically closed the lock after control the main lock and lock hasp in place, and the main lock in standby state.
2）When the main lock and the lock hasp is separate, the main lock will in standby state, then the lock is in the best way to save electricity .
⑨ Install hole of the main lock and the lock hasp
Install hole of the main lock：5 — 4*25 self-taped
Install hole of the lock has：4 — 4*25 self-taped
⑩ (Back) When install the lock, please use the 3M glue Before use the 3M glue to install the lock, please make sure the install way is smooth and clean
1. When in low battery condition, the lock will flicker and the buzzer will alarm to notice user to change the battery, but it also can be use about 1 month.
2. If the low battery condition is continue, the lock will flicker and the buzzer will alarm, and it will automatically cut off the lock function.
3. When the battery is lower than the minimum power set by the lock, the remote lock will automatic open. This function is avoid user go out for a long time and after the change battery function alarm but it still can’t be changed. It can impede user can’t open the door when the battery with no power completely.
4. In order to avoid the automatic lock which reduces the safety of the lock, please replace the battery when user will go out for a long time.
1. When the LED light is flicker, the voice of the lock will weaker,then it must be changed the battery.
2. According to the direction of the arrow to open the battery cover,put 2 AAM battery in it (Please insert the new battery after 10 seconds to protect the electronic circuit).
3. Then open and close the door to check if the new battery is good.
Note: Please use alkaline battery, the magnetic battery or the rechargeable battery will make the lock break down.
1. When the LED light is dark and the control speed is slow, please change the battery in the remote control.
2. Use a small size tool inserts the flank and rotates the tool to open the cover, the battery is CRC2032, and pay attention to the polarity of the battery. The install order: the front cover, rubber blanket, the electronics circuit board and the back cover.
3. After change the battery, please check whether remote control can work.
1.Open the cover of the main lock
2.Under the battery jar, there is a match code key (as Pic. ⑤）；
3.Continue to press the match code key 3 seconds；
4. The LED for the main lock will flicker and a “drops”
5. Press each remote control for 1 second, each main lock will have a “drops”, that means match code success. (Note: If user install the fingerprint terminal outdoor, user can register a finger on the terminal, there is a “drops” when press finger on the terminal,that means match code success )
6.Press the match code key 1 second on the main lock, after there is a “drops” on the main lock, it means stop to match code.
7. Finish match code, please check the fingerprint terminal and remote control.
8.When one of the controller can’t work , please according to the above step to rematch code again.
1. If use lose one remote control, please rematch code all the remote controls.
2. After rematch code, all the lost controllers are useless.
Note: Unless lost a remote control, or to buy a new remote control, otherwise don\'t press the code key on the main lock. Because press the code key means delete all the original code, then need to rematch.